I’m With The Band Theory

We have already talked about the mechanical aspects of how a solid is assembled from individual atoms, when the atoms are in a repeating periodic structure called a crystal lattice. The lattice type can determine many of the material properties, but one of the most interesting and useful properties to think about is electrical conduction. One of the simplest ways to measure conduction is by creating a potential difference, so that one side of the material is more energetically favorable to charged particles than the other. This is called applying a voltage, named after Alessandro Volta who invented the battery, a device that uses chemical differences to create a voltage. When there is a voltage applied, electrons are drawn through the material, but how many electrons flow (which determines how large the measured electrical current is) varies widely by material. In some solids where electrons move freely, it’s easy to pass a lot of electrons through, creating an electrical current. This is characteristic of a metal, where electrical conduction is easy. But in other solids, it takes a lot of energy to move electrons through so electrical conduction is difficult, and we say these materials are insulators. And there is a third class of material, a semiconductor, which can be switched between conducting and non-conducting states.

To understand what causes the different electrical behaviors, we can think about how the atomic energy states available to electrons scale up to a bulk material. Each individual atom has a set of available electron states, that can be mathematically described using quantum mechanics. Some of these states are occupied by electrons, and some are not. A collection of atoms will have a collection of states, some occupied and some free, and an electron has to have available states that it can move between in order to traverse a solid. If there are no available states, it doesn’t matter how energetically favorable it is for the electron to go somewhere else, it has no way of getting there.

For a solid made up of only one kind of atom, the electronic states in each atom will be similar but may vary slightly due to varying conditions throughout a non-perfect crystal. This means that if we sum up all the states, instead of the precisely delineated states we found in a single atom, we’ll have smeared out bands of available states and forbidden regions which give a rough approximation of what energies electrons can have. As usual, the lowest energy states will be mostly occupied, and the highest energy states will be mostly empty. It’s the states right at the top of the electron occupancy which turn out to be the most useful for conduction, because of the minimal energy cost involved in moving electrons. (The line demarcating this is called the Fermi energy or Fermi level.) And how these available electron states look when we depict them as a function of energy can be very different, as shown below:

The various bands of allowed electronic states can overlap with each other, can have a small separation in energy, or can have a large separation in energy. Overlapping bands mean that in both bands, electrons have many available states to transition to, and that is why materials with overlapping bands have high electrical conductivity. These are metals, like gold or copper. For materials with a large separation between bands, the lower energy band is completely full and the higher energy band is completely empty. If an electron in the full band is tempted to move through the material, it must first scrounge up the energy to jump up to an available state, which is so considerable a task that most electrons can’t manage it. These are insulators, which may only pass one electron for every 1030 (a billion billion billion, or more electrons than stars in the universe) that pass through a metal at the same potential.

But the most interesting case, at least as far as modern electronics is concerned, is the material with a small separation between bands, the semiconductor. Only a small energy is needed to boost an electron from the full band to the empty band, and if the energy required is provided by thermal energy at room temperature, semiconductors can have significant electrical conduction at room temperature. But the most useful semiconductors are not quite conductive under normal conditions, but can easily be turned on by applying an electric field. That means they can operate as an electrical switch, acting as a metal or an insulator depending on what’s required. Silicon is the most widely used semiconductor in the present day,

Where the bands of available states fall exactly is determined by the crystal lattice type and the interatomic spacing, two factors which are themselves determined by the outer electrons of the atoms themselves. And for amorphous solids without a periodic structure, like glass, we still get energy bands. In fact, one way to think of the transparency of glass is that visible photons entering the material do not have enough energy to excite electrons from a filled band into an empty band, so they pass through the material without interacting with it. And that’s why you can see through glass!

All the justification for band theory involves a lot of math, of course. But just the basic idea, that bulk materials have bands of available states for electrons and the energy and grouping of these states determines electrical behavior, is pretty amazing because it puts a framework around the broad variety of electrical behaviors that we see in materials in nature. And, if you want to understand how electronics work, band theory is the first big piece of that puzzle.

Advertisements

9 responses to “I’m With The Band Theory

  1. Pingback: How Resistors and Capacitors Work | letstalkaboutscience

  2. Pingback: Electrons and Holes | letstalkaboutscience

  3. Pingback: Electronics: The Bigger Picture | letstalkaboutscience

  4. Pingback: Photoelectric Interactions | letstalkaboutscience

  5. Pingback: Defects in the Crystal Structure of Materials | letstalkaboutscience

  6. Pingback: Why The Nanoscale Matters | letstalkaboutscience

  7. Pingback: Topic Index | letstalkaboutscience

  8. Pingback: Happy Ada Lovelace Day! | letstalkaboutscience

  9. Pingback: Thermoelectrics and the Movement of Electrons | letstalkaboutscience

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s